Hose Barbs
The Type I (QCC) connectors (ME517, ME518 and ME519 Series) are designed with a built-in excess ow feature and a positive shutoff that will not allow gas to ow until the connector is fully engaged. In case of a fire the built-in thermal protection on the QCC connector melts allowing the nipple to disengage from the tank connection and stop the ow of propane. These QCC connectors also provide a positive back check seal at disconnect to eliminate the propane in the hose from being released into the atmosphere.
- Inlet: 1-5/16 in. female acme
- Flow capacity: 100 SCFH air/200,000 BTUH
- Thermal protection
- 1/4 in. hose barb
MEC # ME1656 is a refillable cylinder fitting. Soft Nose POL with 1/4 Barbed Hose Fitting. Brass with Plastic Hand wheel. No Excess Flow Valve.
- Plastic hand wheel fits over the hex fitting to enable hand tightening of the POL connection
- Inlet: POL with rubber seal O-ring
- Outlet: 1/4 in. barbed gas line fitting (fits 1/4 in. I.D. hose size)
- No excess flow valve item # ME1655 is available with 0.9 GPM excess flow valve
Marshall Excelsior ME496 propane cylinder adapter. 1/4 in. Hose Barb x 1 in. 20 Male Swivel with Valve Stem and O-ring. Solid brass construction.
- Durable construction
- Good quality
- Barbed fitting for a tight seal on hoses
- Brass for corrosion resistance, ductility at high temperatures and low magnetic permeability
Full Flow. Pol X 1/4" Barb with 7/8" Hex Nut. MUST BE INSTALLED BY TRAINED PERSONNEL IN ACCORDANCE WITH NFPA 58 & 54 STATE AND LOCAL CODES
- Male POL x Hose Barb fitting
- Heavy duty brass construction
- Hard Nose POL
- Hose ID: 1/4"
Hose fittings connect, control, change the direction of, and terminate the flow in piping and hose systems. This adapter is for connecting a hose to a male threaded connection of a different diameter. Hose barb on one end and male NPT threads on the other. Brass for corrosion resistance, ductility at high temperatures, and low magnetic permeability.
- Barbed fitting for a tight seal on hoses and NPT threads for a tighter seal than straight threads
- Barb x 3/8 in. female flare swivel
- Contains lead
- For use with plastic or rubber hose
- Nut: 3/8 in. Female flare swivel
- Hose barb: 3/8 in.
The ME1654AH Soft-Nose POL Adapter is machined of solid brass (excluding the plastic hand wheel). The 1/4 MNPT fits the inlet of all standard low-pressure regulators. Requires a wrench.
- Caution: do not use soft-nose POLs in any installation where extreme vibration is present replace O-ring
- Full flow
- Hex hand wheel
- Durable all brass construction
Disposable Propane Tank Adapter. 1 in. -20 Female Swivel x 1/4 in. Hose Barb, High Pressure. Brass.
- Camping fitting
- Inlet: 1 in. - 20 in. female
- Outlet: 1/4 in. hose barb
- High pressure, no valve, straight through inside
- Durable brass construction
- MEC part# ME484
Can be used which makes them an economical choice. For use with copper, brass, aluminum and welded steel hydraulic tubing that can be flared. Not for underground use.
- Withstand temperatures up to 212 degree F
- Pressure up to 150 psi
- Brass
- 2-year warranty against defect
- Leaded
- Adapter
Can be used which makes them an economical choice. For use with copper, brass, aluminum and welded steel hydraulic tubing that can be flared. Not for underground use.
- Withstand temperatures up to 212 degree F
- Pressure up to 150 psi
- Brass
- 2-year warranty against defect
- Leaded
- Adapter
Can be used which makes them an economical choice. For use with copper, brass, aluminum and welded steel hydraulic tubing that can be flared. Not for underground use.
- Withstand temperatures up to 212 degree F
- Pressure up to 150 psi
- Brass
- 2-year warranty against defect
- Leaded
- Adapter
Can be used which makes them an economical choice. For use with copper, brass, aluminum and welded steel hydraulic tubing that can be flared. Not for underground use.
- Withstand temperatures up to 212 degree F
- Pressure up to 150 psi
- Brass
- 2-year warranty against defect
- Leaded
- Adapter
Can be used which makes them an economical choice. For use with copper, brass, aluminum and welded steel hydraulic tubing that can be flared. Not for underground use.
- Withstand temperatures up to 212 degree F
- Pressure up to 150 psi
- Brass
- 2-year warranty against defect
- Leaded
- Adapter
Can be used which makes them an economical choice. For use with copper, brass, aluminum and welded steel hydraulic tubing that can be flared. Not for underground use.
- Withstand temperatures up to 212 degree F
- Pressure up to 100 psi
- Brass
- 2-year warranty against defect
- Leaded
- Adapter
Can be used which makes them an economical choice. For use with copper, brass, aluminum and welded steel hydraulic tubing that can be flared. Not for underground use.
- Withstand temperatures up to 212 degree F
- Pressure up to 150 psi
- Brass
- 2-year warranty against defect
- Leaded
- Adapter
Can be used which makes them an economical choice. For use with copper, brass, aluminum and welded steel hydraulic tubing that can be flared. Not for underground use.
- Withstand temperatures up to 212 degree F
- Pressure up to 150 psi
- Brass
- 2-year warranty against defect
- Leaded
- Adapter
Can be used which makes them an economical choice. For use with copper, brass, aluminum and welded steel hydraulic tubing that can be flared. Not for underground use.
- Withstand temperatures up to 212 degree F
- Pressure up to 150 psi
- Brass
- 2-year warranty against defect
- Leaded
- Adapter
Can be used which makes them an economical choice. For use with copper, brass, aluminum and welded steel hydraulic tubing that can be flared. Not for underground use.
- Withstand temperatures up to 212 degree F
- Pressure up to 100 psi
- Brass
- 2-year warranty against defect
- Leaded
- Adapter
Can be used which makes them an economical choice. For use with copper, brass, aluminum and welded steel hydraulic tubing that can be flared. Not for underground use.
- Withstand temperatures up to 212 degree F
- Pressure up to 150 psi
- Brass
- 2-year warranty against defect
- Leaded
- Adapter
Can be used which makes them an economical choice. For use with copper, brass, aluminum and welded steel hydraulic tubing that can be flared. Not for underground use.
- Withstand temperatures up to 212 degree F
- Pressure up to 150 psi
- Brass
- 2-year warranty against defect
- Leaded
- Adapter
Can be used which makes them an economical choice. For use with copper, brass, aluminum and welded steel hydraulic tubing that can be flared. Not for underground use.
- Withstand temperatures up to 212 degree F
- Pressure up to 150 psi
- Brass
- 2-year warranty against defect
- Leaded
- Adapter
Can be used which makes them an economical choice. For use with copper, brass, aluminum and welded steel hydraulic tubing that can be flared. Not for underground use.
- Withstand temperatures up to 212 degree F
- Pressure up to 150 psi
- Brass
- 2-year warranty against defect
- Leaded
- Adapter
Can be used which makes them an economical choice. For use with copper, brass, aluminum and welded steel hydraulic tubing that can be flared. Not for underground use.
- Withstand temperatures up to 212 degree F
- Pressure up to 150 psi
- Brass
- 2-year warranty against defect
- Leaded
- Adapter